If you are unable to connect to a flash-based device, keep in mind that pre-loaded code may prevent it from properly connecting. The JTAG debugger is not powered (some variants of XDS560 and XDS560v2). The explanation is: One of the FTDI driver functions used during configuration returned a invalid status or an error. This test will be applied just once. http://dukesoftwaresolutions.com/an-unknown/an-unknown-error-occurred-2131.html
Your Chromebook can connect to the following types of devices: MTP devices (read only) USB keyboards (Windows and Mac) USB mice with the following features: left button, right button, scrollwheel USB... C28x the debug probe reported an error This error is commonly associated with C28x devices and is usually associated with a range of hardware or firmware problems that prevent the JTAG If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. Helpful (0) Reply options Link to this post by Nemmy, Nemmy Jan 9, 2008 11:34 AM in response to SultanDog Level 1 (0 points) Jan 9, 2008 11:34 AM in response https://discussions.apple.com/thread/1144796?tstart=0
I have bought tunes on I-tunes so really want to put these onto a cd. Check their pages at XDS560 and XDS560v2 System Trace. This can be caused by either an unreliable USB connection (data is corrupted going to or from the FTDI chip), hardware problems (the FTDI chip in the XDS100 is not responding Poor cable quality has resulted in failures during Windows/Linux device driver intialization or during a CCS debug startup/connect.
If not, you are risking losing your music and playlists.... 09-15-2007, 12:22 AM #5 StephenDest Freshman Lounger Join Date: Sep 2007 Posts: 10 permalink I have a similar If one fails put it to the side and use another. The Unknown Error Occured 2131 error is the Hexadecimal format of the error caused. An incomplete installation, an incomplete uninstall, improper deletion of applications or hardware.
The only advice I can find about this error suggests upgrading from 7.3, but I am already using the latest version of iTunes (184.108.40.206). How does it work? The debug probe firmware is incompatible with the OS. http://unknown.error.occurred.2131.itunes.winwizards.org/ It can also be caused if your computer is recovered from a virus or adware/spyware attack or by an improper shutdown of the computer.
Others have said that using CD-RW to burn from iTunes, then use other software to change to CD-R works. I have rebooted my computer and installed ITunes to no avail. The Linux udev rules are not properly configured. All the above actives may result in the deletion or corruption of the entries in the windows system files.
Date Updated: 12/04/2013 Why does my Acer desktop constantly restart after using the backup media I created to restore? When I tried to install this update, I could make it through step 4 before getting a message that read, "The firmware is not supported on this drive." I then tried If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. If this is your first visit, be sure to check out the Forum FAQ and Forum Policy.
run the 'Test Connection' script in the CCSv6 target configuration tab --> FAIL with log shown in previous post (error code -150) run dbgjtag tests WITH reset (integrity, broken, path length, navigate here You can try to workaround or solve this issue by swapping the JTAG debug probe and/or target device or board. If the pin is on the connector that plugs into the target board, it is often called Cable Break Far or sometimes just Cable Break. Download the file and extract it to a folder.
Check the Windows Control Panel or the XDS200 known issues. Trouble Halting Target CPU: Error 0x80001820/-2062 Fatal Error during: Execution, Timeout, Target, Cannot halt the processor This is an error that was recovered but the code integrity is unknown. Thank you so much!!!
Note: The manual fix of Unknown Error Occurred 2131 Ituneserror is Only recommended for advanced computer users.Download the automatic repair toolinstead. Scan tests: 1, skipped: 0, failed: 0 Do a test using 0x00000000. Please check this post for additional details and this post for a way to recover the development board. However, if the error happens later in the debug session the reasons are different (perhaps the reliability of the JTAG connection due to noise, etc.).
The Unknown Error Occured 2131 error may be caused by windows system files damage. Also, each item is followed with some common scenarios described in the Common Errors topic below. 1. Test 1 Word 0: scanned out 0xFFFFFFFF and scanned in 0xFFFFFFC1. http://dukesoftwaresolutions.com/an-unknown/an-unknown-error-occured-6999.html An unknown error occurred (2131)." I have emailed support twice and have gotten responses with numerous trouble shooting ideas...all to no avail.
The previous page with legacy information is still available at the Debugging JTAG Connectivity Problems legacy page. The discussions below cover some possible root causes for this issue: https://e2e.ti.com/support/microcontrollers/c2000/f/171/t/270397 https://e2e.ti.com/support/microcontrollers/c2000/f/171/p/180790/653247 Invalid parameters or command This is a very rare error and indicates the version of the JTAG debugger It can also be caused if your computer is recovered from a virus or adware/spyware attack or by an improper shutdown of the computer. To verify this you can check the steps shown in the Firmware update section for XDS110 and XDS200.
Both a disconnect and power cycle will be required, but there is a possibility the running firmware on the device may be preventing the JTAG debugger from properly connecting (if the This is common error code format used by windows and other windows compatible software and driver vendors. C28xx: Error connecting to the target: (Error -1135 @ 0x0) The debug probe reported an error.