Home > An Unknown > An Unknown Error Prevented The Emulator From Accessing The Processor

An Unknown Error Prevented The Emulator From Accessing The Processor

It doesn't allow single stepping after the first loop.   I have used expf, logf and a c function for exponential integral. Our USB 2.0 emulator is currently being tested with the CCS release of RTDX for the C28x device family. The idea here is to program the flash with code to put it into an infinite loop allowing CCS to halt each core and start up. You should not see this dialog, however it can happen if CC_APP.exe has problems and remains in memory. http://dukesoftwaresolutions.com/an-unknown/an-unknown-error-occurred-while-accessing.html

See slide 57 of:http://processors.wiki.ti.com/images/0/09/CCSv4_Tips_%26_Tricks.pdf FYI - since you are using a multi-core device, Debug Active Project will try to connect, load and run to the first CPU in the scan chain It is recommended to RESET EMULATOR. Sequence ID: 70 Error Code: -1060 Error Class: 0x00000002 Trouble Writing Memory Block at 0x78000014 on Page 0 of Length 0x4: Error 0x00000002/-1060 Error during: Memory, An unknown error prevented the I am using CCSVersion: 4.0.1.01001 and XDS510 USB PLUS.

The main problem we have had with the C55x device has been that Rev 2.x has an 8 bit BYPASSin the scan chain, so when you setup CCS with the C55x TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at Do I need to update my Blackhawk Emulation Drivers? And then I went through http://processors.wiki.ti.com/index.php/Debugging_the_DSP_side_of_a_DSPLink_application_on_OMAP_using_CCSand changed the examples as mentioned.

If this is a multi-core system, the master CPU may not be releasing the DSP/MCU from reset. Is the USB 2.0 emulator comparable with the XDS510-class emulators from TI or are there differences? This will disconnect each target from the emulator. If not, PLEASE read it.

Do Blackhawk emulators support +3.3V and +5V JTAG interface (14 Pin)? Error connecting to the target: Error 0x80000244/-1178 Fatal Error during: Register, Initialization, OCS, The target does not have a CPU clock. Any idea[*I] what I should look at to find out what is causing this annoying problem? Note: You must do this edit everytime you run setup until TI issues an update that fixes their problem.

We cannot implement a workaround. Did you read theCCS Forum Guidelines & FAQ? Will Blackhawk emulators work with CCS2.20 Eval version? However, I was still receiving error message for DSP side.

I have put a breakpoint before a loop. > The execution goes though a loop once and never comes back to the breakpoint > again. Trouble Writing Memory Block at 0x82805a80 on Page 0 of Length 0x104: Error 0x00000022/-1060 Error during: Memory, Execution, An unknown error prevented the emulator from accessing the processor in a timely This will disconnect each target from the emulator. The "560" is the latest emulation technology introduced by TI in May 2002.

It is recommended to RESET EMULATOR. http://dukesoftwaresolutions.com/an-unknown/an-unknown-error-has-occurred-while-accessing-flash.html The code > running is for speech enhancement. GEL_MapAdd( 0x78000000, 0, 0x08000000, 1, 1 ); /* EMIF B Control */ GEL_MapAdd( 0xA0000000, 0, 0x10000000, 1, 1 ); /* EMIFA CE2 - CPLD */ Regards, Titus S. Our TALON OS is POSIX-compliant for TI TMS320 DSPs.

For the OMAP platform, it has been noticed that the ARM core of the device boots and causes contention with CCS and the emulator. com/blogs- 1/nf/Mike_ Dunn.php You might also like... Of course, on USB 1.1, which is only rated for 12Mbit/sec transfer rate (1.5MByte/sec), we have some limits on the 2MByte HS-RTDX channel. Check This Out Sequence ID: 70 Error Code: -1060 Error Class: 0x00000002 Trouble Writing Memory Block at 0x70000020 on Page 0 of Length 0x4: Error 0x00000002/-1060 Error during: Memory, An unknown error prevented the

We support Code Composer v4.1x, CCS v1.2, and CCS v2.0 and later. Unique to Blackhawk, our XDS560-class emulators support XDS510 drivers by being able to communicate with them or XDS560 drivers. DM648 Davinci Guru 10355 points Eddie3909 Hi The error below occasionally happens but unfortunately it is getting so frequent that I've got to find out why.

Q1.

c.) Save the file. It is possible to hardware modify the emulator to reduce TCK frequency. The USB 2.0 and USB560 JTAG Emulators support all of the devices that TI supports in Code Composer Studio (C2000, C5000, C6000, ARM and OMAP). Our emulators are available from a worldwide network of resellers including Texas Instruments.

The targets should then be power cycled or hard reset followed by an emureset and reconnect to each target. This is specific to Blackhawk XDS560-class emulators. With the USB cable not connected to the emulator, attach the 5 volt power supply, then wait 2 seconds, then connect the USB cable to the emulator. http://dukesoftwaresolutions.com/an-unknown/an-unknown-error-occurred-while-accessing-flash.html I am using 6713 dsk with a USB.

TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these I have a problem with connecting the USB-JTAG Emulator to a TMX320C5510GGW21. This is something unique to our device and extends capabilities to the C24xx and VC33 devices in Code Composer v4.1x. Why?

Please use the latest processor SDK package for your platform (K2H,K2E,C665x,C667x etc.,) http://www.ti.com/lsds/ti/tools-software/processor_sw.page Reply Cancel Cancel Reply Suggest as Answer Use rich formatting Prodigy 185 points nirav desai Dec 26, 2015 After going throughhttp://e2e.ti.com/support/dsp/omap_applications_processors/f/447/t/29982.aspx?PageIndex=1, I removed all the .gel files and then started "Debug Active Project" .